My Top 5 Valentine’s Day DIY Craft: Part 2

My Top 5 Valentine’s Day DIY Craft: Part 2

Hey loves! Who’s ready for day two of the Valentine’s day decor diy? Me, me! If you’re new here, welcome! Today, I’ll be sharing my next Valentine’s day craft. I’m calling it “the heart box!” Shall we begin…

The Heart Box

Materials & Tools:

  • Art decor box (dollar tree find)
  • Metal heart (retrieved mines from a dollar tree sign)
  • Twine (dollar tree)
  • Ribbon (dollar tree)
  • Paint (your choice)
  • Paint Brush 
  • Hot Glue Gun 
  • Gluesticks
  • Sandpaper or Sanding Block
Decor box found at The Dollar Tree in the Valentine’s Day seasonal section.

To get started, take the box and scrap the flower off (your box may differ as there are different prints sold at The Dollar Tree.) I used scissors to complete this process, but I suggest using a putty knife. Grab sandpaper or a sanding block and sand the area so that it’s smooth. Be sure to wipe the area clean, free of dust. 

Sanding to smooth the area. Don’t forget to wipe the residue off.

Next, I mixed my three paints together as I did in my previous post (see here) to get my desired pink color. Use a paint brush to brush on the paint, then allow to dry.

After drying, add a dab of  hot glue to secure the tip of the twine to the back of the box. Next, wrap the twine around 4 times. Cut, and then glue the twine to secure in place. Repeat for the remaining 3 sides. 

Applying hot glue to the metal heart, place it to the center of the box. Cut your desired length of the ribbon of your choice and make it into a bow. Add a dab of hot glue and place the bow at the top of the box. There’s your beautiful Valentine’s Day diy decor piece! Another simple and easy win!

I hope you all enjoyed! If you haven’t already, be sure to check out “The Love Sign” in my previous post. Tomorrow, I will introduce my next diy Valentine’s Day decor! Until next time loves!

Processing…
Success! You’re on the list.

Copyright © 2020 Farmhouse Unique | All Rights Reserved

My Top Valentine’s DIY Crafts: Part 1

My Top Valentine’s DIY Crafts: Part 1

Roses are red. Violets are blue. Love is here and forever true. 

Aww love…love is in the air, is it not? Today, I’m going to share one of my top 5 Valentine’s diy crafts that was crafted over the weekend. The other crafts will be shared over the next few days. Each one is inexpensive, simple, and easy to do. Majority of the materials are found at Dollar Tree. So let’s get started!

The love sign

Materials & Tools:

  • Twine (if desired)
  • Paintbrush
  • 1 wood board (this board came from Home Depot …it was leftover from a previous project)
  • Paint tray
  • Paint (color of your choice)

Since I didn’t have a pink that I preferred I mixed white chalk paint with a magenta pink and added a little orange to get the lighter pink hue I applied to the sign.

While allowing the board to dry completely, I sketched out the lettering “L-O-V-E” onto 4 sheets of paper.

Sketch out the letters, and then laid the paper flat on the board to lightly trace over with a pencil.

After the board dried, I then laid each sheet onto the board and lightly traced over the letters one at a time with a pencil, so it will show the imprint on the board. 

After removing the paper, I then treced over the letters with a sharpie paint pen.

Next, remove the paper and outlined over the imprint with a sharpie oil based paint pen in gold, and then filled in the letter. Repeat for the remaining letters. 

For the finishing touch, I wrapped twine around and tie it into a bow. If you would like to be more creative add lights, ribbons, and/or floral to add more beauty. 

Sweet and simple! Until the next craft my darlings!

What’s your favorite thing about Valentine’s day? Is the kiddos exchange Valentine’s cards at school? Crafting? Decorating? Baking? Cooking a nice dinner?Planning a romantic evening? Writing a sweet poem? Picking out a gift? Receiving a gift? Showing your love how much they mean to you? What is it? Let me know in the comments below.

Processing…
Success! You’re on the list.

Copyright © 2020 Farmhouse Unique | All Rights Reserved

How to Build a Baby Gate: 10 Step Process

How to Build a Baby Gate: 10 Step Process

Welcome to the new year of 2020! I hope you all had a great New Years Day! I’m starting the New Year’s off by finishing the build of my second baby gate.

I was in desperate need of a gate since my little mister has successfully climbed over and through everything I’ve used to block his way; a chair,  a large basket filled with blankets, a large pillows, and even bean bag chairs. All were epic fails!

Honestly, I’ve been putting this off for a while now. With so much to do and so little time, things just haven’t been getting done. Now that the holiday season is over, I was finally able to build the gate and can’t wait to start my next project.

Mommy’s travel buddy and I took a ride to Home Depot to gather supplies. We gathered about 6 common boards, hinges, and a lock only to find out that I purchased the wrong boards and lock this time, (this is what happens when you’re short on time and in a rush.)

The lock is smaller than the one I purchased last time, while the boards are much wider and longer than the common boards I used in the previous build of my first  baby gate.

Sighs…No matter though!
I just improvise. 

Different boards mean different gate and I’m fine with that! 

Let’s build!

Materials used:

  • 6- 1 x 5′ x 8′ Common boards
  • Hand saw (suggest a mitre saw or circular saw)
  • Nails & Hammer (Brad Nailer if desired)
  • 2 Hinges
  • 1 Lock
  • Wood stain of your choice
  • Polyethylene (if desired)

Tools used:

  • Hand saw (suggest a mitre saw or circular saw)
  • Sander
  • Drill and/or screwdriver
  • Sponge and/or paintbrush

Step 1: Measure the length between the wall of your stairway or wherever you choose to place your baby gate. Then subtract an inch or 2 off to compensate for the board(s) that you will be attaching to the walls to help hold up the gate. 

Note: This is where I made a mistake by not examining and remeasuring the area before I measured and cut. It wasn’t too much of a disaster,  but it would have saved me from cutting one less board.

Step 2: Measure and cut the boards as you need to equal the width. 

Note: I used the same measurements from my last baby gate diy, but this time with lesser boards and a different style gate.

My Measurements:

39″ width × 33″ height

Step 3: After cutting, sand each board before assembling. 

Note: You could wait to sand until after you assemble. It’s your choice, but I chose to sand everything now.

Step 4: Lay the backframe and spread each board out as equally as possible. Then lay the front frame across on top, making sure they’re aligned with the backframe. 

Note: For the front frame, one board at the top, while the other is at the bottom. See picture below for layout.

2 boards for the front frame; 5 boards for the back frame.

Step 5: Use wood glue and apply a small amount to one board on the back frame. Next, hammer 2 nails to secure the front frame to that board. Repeat the step for the remaining boards.

Step 6: Stain your wood if you dare. Be sure to follow the instructions on the label and allowed it to dry 24 hours before applying polyethylene. 

Note: I used Rust-Oleum American gel stain.

After apply the stain, I allowed the gate to dry 24 hours before apply polyethylene.

Step 7: By following the instructions on the label, apply polyethylene. Also allow 24 hours to dry.

Step 8: Depending on the placement of your gate, you may need to screw one or two board to the wall using 3 drywall screws on each. 

Note: Based on the placement of my gate, I only needed to use one board.

Step 9: Use a drill or a screwdriver to attach the hinges.

After attaching the hinges.

Step 10: Last, but not least, use a drill or screw to attach the lock bolt. 

Note: Based on my placement of the gate, I only used one board for the wall to latch the gate onto. I then attached part of my lock to the gate and then the door frame of my kiddos playroom. (See picture below.)

Lock attached to gate and door frame. Yes, I know it’s a little crooked, but it works!

It was definitely time for another baby gate. I am so thrilled to have finished this project and I’m ready to take on the next one. So with the New Year finally here, I hope to plan accordingly and finish projects one at a time. The bigger projects may occur once a month, while the smaller projects can vary from once a week to every two weeks. Stay humble, plan, and enjoy your year of 2020!

The finish product! As you can see, one board is used to hold up the baby gate, while part of the lock is attached to the door frame.

Stay connected.

Processing…
Success! You’re on the list.

Join our social media and share with your friends and family!

Copyright © 2020 Farmhouse Unique  | All Rights Reserved